Search found 1685 matches
- Sun Dec 11, 2022 10:17 pm
- Forum: Experimenters' & Innovators' forum
- Topic: zoetrope lathe cut 12" vinyl records
- Replies: 6
- Views: 1563
Re: zoetrope lathe cut 12" vinyl records
These are just picture discs. Are you looking for someone to design a zoetrope for you? Or do you have one and just need lathe cuts?
- Mon Nov 14, 2022 3:30 pm
- Forum: Newbie Forum
- Topic: Cutting on to CD
- Replies: 2
- Views: 657
Re: Cutting on to CD
Most people emboss onto cds because they are polycarbonate. My guess is that the polycarb would wear down yr cutting diamond fairly quickly. But you could potentially turn an old, slightly worn diamond around 180 degrees and emboss with it. Tragwag would probably know.
- Thu Nov 10, 2022 7:06 pm
- Forum: Vinyl Mastering, Lacquer cutting, Pro's and others
- Topic: Grampian Type D - Reconditioning
- Replies: 12
- Views: 18087
Re: Grampian Type D - Reconditioning
If you successfully wind a new saddle coil for this, I would be interested in buying a few. I don't have a coil form for it. Thanks!
- Mon Oct 31, 2022 10:27 am
- Forum: Newbie Forum
- Topic: Stuck Between Current Recordio 8j10 Resto or Trying to Find Another Lathe
- Replies: 6
- Views: 4224
Re: Stuck Between Current Recordio 8j10 Resto or Trying to Find Another Lathe
I can get you started with a lathe at the high end of your budget. It will be WAY WAY better than that Recordio, will come with a starter pack of blanks and a needle, and include tech support. I can get you cutting good mid-fi records in about two hours after it arrives. EMail me through www.RecordL...
- Sun Oct 16, 2022 12:17 am
- Forum: Secrets of the Lathe Trolls
- Topic: Presto 1-C vs Fairchild 541a vs RCA 11850 heads
- Replies: 1
- Views: 1383
Re: Presto 1-C vs Fairchild 541a vs RCA 11850 heads
They are all in the same middle range. Quality depends more on the head’s current condition. If i was to roll the dice on them, my order would be RCA (if that is the silver square hifi version. I believe that is the model), Presto, Fairchild.
- Sun Oct 16, 2022 12:14 am
- Forum: Secrets of the Lathe Trolls
- Topic: Rek-o-kut head mount adapters?
- Replies: 1
- Views: 1374
Re: Rek-o-kut head mount adapters?
I sell two different variations on it. Jed’s counterweight with dashpot version and another version that has no dashpot, but has a front spring similar to the 6n weight spring. Dm me
- Fri Oct 07, 2022 9:09 pm
- Forum: Classifieds & tip-offs
- Topic: Looking for Stylus
- Replies: 1
- Views: 1242
Re: Looking for Stylus
Try emailing myshank through the site from tge email address you tried to use and politely request to purchase a stylus. He should respond.
- Fri Oct 07, 2022 8:59 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Anyone tried a Diamond stylus on a 1d cutter head?
- Replies: 3
- Views: 2501
Re: Anyone tried a Diamond stylus on a 1d cutter head?
You can diamond cut pretty loud on a 1d. Maybe not post-loudness wars 80s dance 12”, but much louder than embossing. But it also really depends on the life the cutter head has lived, so your head maybe louder/not than any other 1d.
- Mon Sep 26, 2022 11:48 pm
- Forum: Vinyl Mastering, Lacquer cutting, Pro's and others
- Topic: My Test Pressing Is Not As Bright
- Replies: 4
- Views: 6116
- Mon Sep 05, 2022 10:58 am
- Forum: Secrets of the Lathe Trolls
- Topic: cheap embossing material
- Replies: 4
- Views: 2169
Re: cheap embossing material
Laserdiscs are made of acrylic, unfortunately. They can't be embossed, only cut using no longer readily available cutting sapphires (or diamonds, tho NOT recommended), and the acryclic will wear needles out QUICK. Can be done, but not cost effective AT ALL. You should be able to get polycarbonate sq...
- Sat Aug 27, 2022 11:39 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Mystery cutting head
- Replies: 16
- Views: 14646
Re: Mystery cutting head
Can you post some pictures of what it looks like inside? Take the front cover off? Im very curious.
- Fri Aug 19, 2022 2:26 am
- Forum: Newbie Forum
- Topic: New member Presto 6n resto-mod project
- Replies: 8
- Views: 2429
Re: New member Presto 6n resto-mod project
I think it is just a 6-32 screw that has been milled down on one side and then has a hole drilled in the end. Its not an off the shelf part. Its custom made, but not hard to make with a dremel, a clamp, and a drill press.
- Fri Aug 12, 2022 3:52 am
- Forum: Newbie Forum
- Topic: Hello from Pittsburgh, Helping kids understand vinyl...
- Replies: 3
- Views: 1581
Re: Hello from Pittsburgh, Helping kids understand vinyl...
Al is correct, there is absolutely no way to get started in this hobby for anywhere close to your budget. The recordios are pretty useless in my opinion and i personally wouldnt waste the energy on picking one up on the curb in a free pile. Quality is crazy low and restoration is far more expensive ...
- Thu Aug 11, 2022 4:04 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Lathe meetups: PDX, Minneapolis, Toronto?
- Replies: 0
- Views: 2265
Lathe meetups: PDX, Minneapolis, Toronto?
Hey everyone, im installing lathes in PDX, Minneapolis, and Toronto in the next 3 weeks and would love to meet up with other trolls. We have a PDX meetup this saturday at The Good Foot at 7:30 and the other two locales i’m just looking to see who is out there!
- Tue Aug 09, 2022 2:10 am
- Forum: Newbie Forum
- Topic: First experiences cutting records on a no-frills mono machine – questions how to proceed.
- Replies: 3
- Views: 3907
Re: First experiences cutting records on a no-frills mono machine – questions how to proceed.
• Am I using the right blanks for my setup? Those old steel needles were meant for cutting lacquers, and even on a fresh lacquers rarely sound good now. • Where can I get “fresh” cutting needles? I lay out all the different blank and needle types and which are compatible with which in my Newbie Star...
- Sun Aug 07, 2022 8:48 pm
- Forum: Secrets of the Lathe Trolls
- Topic: (Updated) Lathe Cut Camp #17! Oct 8-10, 2022 Tucson, AZ
- Replies: 4
- Views: 1049
Re: (Updated) Lathe Cut Camp #17! Oct 8-10, 2022 Tucson, AZ
Thanks Phil!
Also, I will have several lathes ready to purchase and Lathe Cut Campers get first crack at em. You can even cut and train on yr lathe while you are here!
Also, I will have several lathes ready to purchase and Lathe Cut Campers get first crack at em. You can even cut and train on yr lathe while you are here!
- Fri Jul 29, 2022 9:35 pm
- Forum: Secrets of the Lathe Trolls
- Topic: (Updated) Lathe Cut Camp #17! Oct 8-10, 2022 Tucson, AZ
- Replies: 4
- Views: 1049
Re: Lathe Cut Camp #16! Sept 24-26, 2022 Tucson, AZ
I got four emails today asking for another LAthe Cut Camp, so I scheduled another on Oct 8-10, 2022 in Tucson. If you are interested, check out www.LatheCutCamp.com
- Fri Jul 29, 2022 3:42 pm
- Forum: Secrets of the Lathe Trolls
- Topic: (Updated) Lathe Cut Camp #17! Oct 8-10, 2022 Tucson, AZ
- Replies: 4
- Views: 1049
Re: Lathe Cut Camp #16! Sept 24-26, 2022 Tucson, AZ
NVM. sold out.
- Tue Jul 26, 2022 11:39 pm
- Forum: Secrets of the Lathe Trolls
- Topic: (Updated) Lathe Cut Camp #17! Oct 8-10, 2022 Tucson, AZ
- Replies: 4
- Views: 1049
(Updated) Lathe Cut Camp #17! Oct 8-10, 2022 Tucson, AZ
I've been getting a lot of requests, and have been finding a lot of lathes in the wild recently, so it's time for another Lathe Cut Camp. Sept 24-26, 2022 in Tucson, AZ (This Camp is PERFECT FOR NEWBIES or Folks who just want to learn how it's done whether they want to start cutting themselves or no...
- Tue Jul 26, 2022 11:37 pm
- Forum: Classifieds & tip-offs
- Topic: LOOKING for full Lathe set up
- Replies: 4
- Views: 1167
Re: LOOKING for full Lathe set up
Hi. I sell Lathes and have a pretty wide range of options and prices. Many need restoration, but can be done quickly once I know which lathe to prioritize. Email me through the "contact us" button at the bottom of this website: https://www.recordlatheparts.com/collections/record-lathes