Grampian c/h
Moderators: piaptk, tragwag, Steve E., Aussie0zborn
Grampian c/h
Hey...anyone have info or docs on a Grampian c/h cutterhead? Thanks...
You do not have the required permissions to view the files attached to this post.
Re: Grampian c/h
Hi There,
Here's some Bracket/Mounting detail that may be useful.
Regards
Soulbear
Here's some Bracket/Mounting detail that may be useful.
Regards
![Wink :wink:](./images/smilies/icon_wink.gif)
![Razz :P](./images/smilies/icon_razz.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
You do not have the required permissions to view the files attached to this post.
Re: Grampian c/h
Hi There,
Almost forgot this too, silly me!! As far as I can tell, your "Laydown Grampian" is a "Variant" but the "Techie Stuff" may well still be relevant.
Regards
Soulbear
Almost forgot this too, silly me!! As far as I can tell, your "Laydown Grampian" is a "Variant" but the "Techie Stuff" may well still be relevant.
Regards
![Wink :wink:](./images/smilies/icon_wink.gif)
![Razz :P](./images/smilies/icon_razz.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
You do not have the required permissions to view the files attached to this post.
Re: Grampian c/h
Thanks much! I'm likely going to sell this one...it came with an rca unit i bought and i have 2 other rca heads...one just rebuilt so i don't really need it. I assume this is a feedback unit which i don't have any experience with or an amp for.
Re: Grampian c/h
Hi There,
Regards
Soulbear
P.S.
Well certainly, if it's configured like the one in those few Photo's, one pair of leads would be for Driving the Cutterhead, the other pair would be the feedback signal. Hope this Helps.bpatric wrote: I assume this is a feedback unit
Regards
![Wink :wink:](./images/smilies/icon_wink.gif)
![Razz :P](./images/smilies/icon_razz.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
P.S.
I'm sure someone here on the forum would give your Grampian a good home. As well as RCA Lathes the Grampian's sit rather well on the UK built MSS Lathes too!!bpatric wrote:it came with an rca unit i bought and i have 2 other rca heads...one just rebuilt so i don't really need it
Re: Grampian c/h
It appears to be non feedback or modified or i can't see where the leftmost terminals go in the mechanism. The tabs are broken off on the back removeable plug. I get 5.6 ohm on the rightmost terminals...no reading on the left.
You do not have the required permissions to view the files attached to this post.
- dubcutter89
- Posts: 359
- Joined: Thu Oct 19, 2006 6:30 am
- Location: between the grooves..
Re: Grampian c/h
Yes, the Grampian Type C is regular moving iron design without the "feedback" coil.
Type C/H should be the same just in the Horizontal case for mounting on some small desktop lathes.
if the magnet is strong should be a nice head for mono dubs..
If you want to get rid feel free to contact me![Smile :-)](./images/smilies/icon_smile.gif)
Cheers
Lukas
Type C/H should be the same just in the Horizontal case for mounting on some small desktop lathes.
if the magnet is strong should be a nice head for mono dubs..
If you want to get rid feel free to contact me
![Smile :-)](./images/smilies/icon_smile.gif)
Cheers
Lukas
Wanted: ANYTHING ORTOFON related to cutting...thx
Re: Grampian c/h
Thanks for the info! When i get the lathe running I'll give it a listen..it's an rca 70c with11852 "recording attachment"...like the screen shot here.
You do not have the required permissions to view the files attached to this post.
- dubcutter89
- Posts: 359
- Joined: Thu Oct 19, 2006 6:30 am
- Location: between the grooves..
Re: Grampian c/h
RCA 70 are not as common as the presto and rek-o-kut Units but should give decent results when proper set up!
btw, heres a Little info i once took somewher from the net...
Lukas
btw, heres a Little info i once took somewher from the net...
Lukas
You do not have the required permissions to view the files attached to this post.
Wanted: ANYTHING ORTOFON related to cutting...thx
Re: Grampian c/h
Fantastic! Thanks!