Hi there,
I am very interested in most of this gear.
Please DM me your email address and I can make you an offer.
Search found 12 matches
- Tue Dec 26, 2023 9:35 am
- Forum: Classifieds & tip-offs
- Topic: Stereo Lathe Equipment for sale (Vinylium, Vinyl Recorder etc.)
- Replies: 23
- Views: 68052
- Sat Nov 18, 2023 9:08 am
- Forum: Classifieds & tip-offs
- Topic: Viryl Warmtone automatic press for sale
- Replies: 4
- Views: 7814
Re: Viryl Warmtone automatic press for sale
Where are you located?
- Sat Jul 23, 2022 9:09 am
- Forum: Secrets of the Lathe Trolls
- Topic: Wonky precision platter VR
- Replies: 5
- Views: 1764
Re: Wonky precision platter VR
It's true that it's been awhile since i've serviced my 1200. I will take it in for a full examination.
Thanks for the suggestions
Thanks for the suggestions
- Fri Jul 22, 2022 8:57 am
- Forum: Secrets of the Lathe Trolls
- Topic: Wonky precision platter VR
- Replies: 5
- Views: 1764
Re: Wonky precision platter VR
Thanks for your reply.
Ya there has always seemed to be a "correct" orientation of the brass tightening disk and unfortunately flipping it doesn't solve my issue.
Unfortunately there seems to be a deeper issue at hand.. Still not sure :/
Any other thoughts?
Ya there has always seemed to be a "correct" orientation of the brass tightening disk and unfortunately flipping it doesn't solve my issue.
Unfortunately there seems to be a deeper issue at hand.. Still not sure :/
Any other thoughts?
- Wed Jul 20, 2022 1:33 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Wonky precision platter VR
- Replies: 5
- Views: 1764
Wonky precision platter VR
Hello! An unusual issue has come up with my precision platter from Souri. I've been cutting with the same setup for years (standard VR setup with technics 1200 and precision plate with external motor) and only since recently moving my lathe and setting it up again has this problem started. When I ca...
- Mon Oct 12, 2020 4:11 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Peculiar surface noise cause VR
- Replies: 9
- Views: 3703
Re: Peculiar surface noise cause VR
Thanks for the input everyone My heating wires are connected and the circuit is working. And actually the noise goes away with lots of stylus heat (around 30 on the dial with Souri stylus). I'm getting good sounding cuts now like this however I've been getting equally as clean cuts with very little ...
- Sat Oct 10, 2020 1:06 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Peculiar surface noise cause VR
- Replies: 9
- Views: 3703
Re: Peculiar surface noise cause VR
I Changed the dashpot oil and the noise remains! :s
Any other suggestions??? This noise is haunting me!
Any other suggestions??? This noise is haunting me!
- Sat Oct 10, 2020 8:48 am
- Forum: Secrets of the Lathe Trolls
- Topic: Peculiar surface noise cause VR
- Replies: 9
- Views: 3703
Re: Peculiar surface noise cause VR
Good suggestion. I will change the dashpot oil today.
Thanks!
Thanks!
- Fri Oct 09, 2020 5:05 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Peculiar surface noise cause VR
- Replies: 9
- Views: 3703
Peculiar surface noise cause VR
Hey Trolls! I’ve got a very frustrating surface noise issue on my VR. It’s peculiar as it is happening with different newly sharpened styluses (Souri and Myshank) as well as with Souri and Myshank blanks. Been happily cutting for years with clean cuts but I’ve been struggling with this noise for a m...
- Mon Jul 29, 2019 8:51 am
- Forum: Secrets of the Lathe Trolls
- Topic: Surface Noise with VR
- Replies: 5
- Views: 1388
Re: Surface Noise with VR
Thanks. Ya i've adjusted it but haven't actually removed it and put it back in.
I will try and let you know!
I will try and let you know!
- Sat Jul 27, 2019 1:00 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Surface Noise with VR
- Replies: 5
- Views: 1388
Re: Surface Noise with VR
Thanks for your reply!
I have another freshly sharpened diamond in the mail from Souri right now. Eager to receive it to do some tests and to get comfortably cutting again.
I will post some audio of the surface noise as soon as I get a chance.
Thanks!
I have another freshly sharpened diamond in the mail from Souri right now. Eager to receive it to do some tests and to get comfortably cutting again.
I will post some audio of the surface noise as soon as I get a chance.
Thanks!
- Fri Jul 26, 2019 10:38 am
- Forum: Secrets of the Lathe Trolls
- Topic: Surface Noise with VR
- Replies: 5
- Views: 1388
Surface Noise with VR
Hi trolls! Long time reader first time poster here. Been cutting on my VR for about a year and although i’ve had plenty of issues along the way i’ve always been able to figure them out.. This time I can’t figure it out though! I was cutting along one day when seemingly all of a sudden (realistically...