Search found 199 matches
- Mon Mar 07, 2016 11:34 am
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
How are you guys making the plastic cones? I tried to make some out of thin plastic sheet, and they're not perfectly round, and 2-part epoxy just peels off (it's PVC). I'll post pictures later
- Sat Feb 13, 2016 5:36 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Measuring weight/counterweight?
- Replies: 7
- Views: 1460
Re: Measuring weight/counterweight?
I've been trying to use the spring scale, and maybe I'm not understanding how I should be measuring... As I lift the spring scale up, the measured weight goes up and it lifts the head bracket up. Do I want to take measurements in the position that it's in during cutting for both weight and counterwe...
- Fri Feb 12, 2016 9:43 am
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
- Thu Feb 11, 2016 3:09 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
Yah I took it apart. There's nothing left of the housing it's glued in. I can take pictures of what it looks like without the housing
- Thu Feb 11, 2016 12:13 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
There's a screw in the back with a sticker over it so you should be able to get to it easily. In retrospect, I should have just dremel-ed the grille off.. Would have been much easier to deal with.
- Thu Feb 11, 2016 11:02 am
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
THey are threaded in the back, but they're hard to get the driver out because they're glued in a housing.
- Thu Feb 11, 2016 9:43 am
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
Hey Scotty when you get a chance, can you take pictures of your head with the new stylus holder?
I'm going to try making a head, I got Lanzar TWS 1" titanium dome tweeters
I'm going to try making a head, I got Lanzar TWS 1" titanium dome tweeters
- Wed Feb 10, 2016 1:30 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
Sounds great!!
So you used a 340p stylus? How did you make the stylus holder?
So you used a 340p stylus? How did you make the stylus holder?
- Tue Feb 09, 2016 6:40 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
Very awesome, inspiring work!
- Tue Feb 09, 2016 4:56 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
How are the high frequencies? It seems like that screw you have holding the stylus would add a bit of mass
- Mon Feb 08, 2016 8:45 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
So it seems like the stylus holder is the last piece of the puzzle. For that I'd think you'd need a tapered reamer. Has anyone done anything else?
- Sun Feb 07, 2016 11:44 am
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
How did you make the cone?
- Sun Jan 10, 2016 10:23 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Measuring weight/counterweight?
- Replies: 7
- Views: 1460
Re: Measuring weight/counterweight?
Using a spring scale, do I keep pulling it up until the point just before the head starts lifting..?
- Sun Jan 10, 2016 6:58 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Measuring weight/counterweight?
- Replies: 7
- Views: 1460
Measuring weight/counterweight?
Ok, so I have a DIY lathe that is similar to a Presto with regards to how the head is held (a bearing that the cutterhead is attached to, and an adjustable spring). I also have a spring scale. How do I go about measuring the counterweight and weight? For weight I'm assuming I take the measurement wh...
- Thu Jan 07, 2016 9:59 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
Is this the same silicone rubber? http://www.smooth-on.com/Silicone-Rubber-an/c2_1113_1136/index.html
- Tue Jan 05, 2016 4:55 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
Where did you get the bead from to fit the diamond into? I thought you needed a tapered hole
- Tue Dec 29, 2015 2:12 pm
- Forum: Experimenters' & Innovators' forum
- Topic: Who can help me with my VR T560 cutterhead?
- Replies: 430
- Views: 75464
Re: Who can help me with my VR T560 cutterhead?
How thick are the wires that come out of the cones and connect to the stylus holder? Can you tell what type of material it is?
- Thu Dec 24, 2015 8:31 am
- Forum: Secrets of the Lathe Trolls
- Topic: original RIAA curve with T560 (bypass souri's main unit)
- Replies: 23
- Views: 4996
Re: original RIAA curve with T560 (bypass souri's main unit)
I've used the CurveEQ VST plugin in the past for making EQ corrections.. it's pretty nice, you can take a source file, cut it, record it back, and come up with an EQ curve that will make your source cut correctly. http://www.voxengo.com/product/curveeq/ I believe the trial version will let you test ...
- Mon Oct 05, 2015 10:59 am
- Forum: Plating and Pressing
- Topic: Pressing Shellac Records?
- Replies: 42
- Views: 9430
Re: Pressing Shellac Records?
I wonder if acrylic would work... It doesn't emboss, doesn't scratch easily.
- Fri Sep 04, 2015 9:08 am
- Forum: Experimenters' & Innovators' forum
- Topic: Embossing tech - talk
- Replies: 22
- Views: 5465
Re: Embossing tech - talk
Maybe this is a stupid question, but isn't it pretty dangerous putting lighter fluid/charcoal lighter fluid underneath a heat lamp and around all the electronics and everything? I've been wanting to try it, but I can't bring myself to do it.