vinyl recorder with precision motor
Moderators: piaptk, tragwag, Steve E., Aussie0zborn
Re: vinyl recorder with precision motor
i set cutterhead as possible as parallel with earth.please take a look pic.
(i ask to souri about screw.but he still reply me...)
but problem still don't go away....
it' not complete parallel,but i think it can tolerance.how about?
last way is change turntable bearing to new one.
can anyone show other point?
i still need your help.
any help would be appreciated!
best regard,
marcy
(i ask to souri about screw.but he still reply me...)
but problem still don't go away....
it' not complete parallel,but i think it can tolerance.how about?
last way is change turntable bearing to new one.
can anyone show other point?
i still need your help.
any help would be appreciated!
best regard,
marcy
You do not have the required permissions to view the files attached to this post.
Re: vinyl recorder with precision motor
imho, setting "pararell to earth" isn't a good thing. Unless you did the same with your working table, VR table, VR turntable, and VR haevy platter. Then it's OK. If you don't do it, keep it pararell to the platter.
Re: vinyl recorder with precision motor
hi sat159p1,
thank you for reply.
sorry what mean working table?
anyway also cutterhead holder(sorry,i said "cutterhead" at last post,The correction is "cutterhead holder") is parallel to the platter.
(platter is set parallel to earth.)
what do you say?
i still need help.
any advice would be appreciated!
thank you for reply.
sorry what mean working table?
anyway also cutterhead holder(sorry,i said "cutterhead" at last post,The correction is "cutterhead holder") is parallel to the platter.
(platter is set parallel to earth.)
what do you say?
i still need help.
any advice would be appreciated!
Re: vinyl recorder with precision motor
i disassembled turntable bearing and clean them.then used oil.
but problem still remain...
i appreciate your continued support!
but problem still remain...
i appreciate your continued support!
You do not have the required permissions to view the files attached to this post.
Re: vinyl recorder with precision motor
this is no good thing, i recommend to try with a new spindle.
You do not have the required permissions to view the files attached to this post.
Re: vinyl recorder with precision motor
Hi Gus,
Thank you for showing your opinion!
Now I'm waiting new bearing.
I'll post again when I receive it and use it.
Thank you your continued support!
Thank you for showing your opinion!
Now I'm waiting new bearing.
I'll post again when I receive it and use it.
Thank you your continued support!
Re: vinyl recorder with precision motor
Hi everybody,
I use new turntable bearing.
Finally my Problem went away!
Groove is stable.I'm so happy!!!
Thank you very much who advice me!!
Marcy
I use new turntable bearing.
Finally my Problem went away!
Groove is stable.I'm so happy!!!
Thank you very much who advice me!!
Marcy
Re: vinyl recorder with precision motor
marcy108 wrote:Hi everybody,
I use new turntable bearing.
Finally my Problem went away!
Groove is stable.I'm so happy!!!
Thank you very much who advice me!!
Marcy
Be careful i think souri didn't calculate his (precision= i'm not sure) platter vs Technics spindle/bearing
That means in the near future maybe will you need again to install a new one Technics spindle/bearing.
It's better to speak with Mike http://www.mikenewaudio.com/bearing.php to find a permanent solution for your problem.
Re: vinyl recorder with precision motor
Hi Marcy,
I'm very happy that you finally managed to resolve your problem!
I consider this thread has vital information for all VR owners so maybe it should be archived for all to discover on a future search.
I'm very happy that you finally managed to resolve your problem!
I consider this thread has vital information for all VR owners so maybe it should be archived for all to discover on a future search.
Re: vinyl recorder with precision motor
thank you for your suggestion.i'll contact him in near future!Gus wrote:Be careful i think souri didn't calculate his (precision= i'm not sure) platter vs Technics spindle/bearing
That means in the near future maybe will you need again to install a new one Technics spindle/bearing.
It's better to speak with Mike http://www.mikenewaudio.com/bearing.php to find a permanent solution for your problem.
thank you,SueDenim!SueDenim wrote:I'm very happy that you finally managed to resolve your problem!
I consider this thread has vital information for all VR owners so maybe it should be archived for all to discover on a future search.
yes,i hope this thread is useful for other VR users.
in the end,thanks again.
i appreciate you all who help me!