Loads of heads, feedscrews, tonearms, etc for sale
Hey everyone,
I'm cleaning out the studio a little bit to help pay for my divorce (and the gear binge depression shopping I've been doing).
I'm selling:
Presto 1C Cutter Head
RCA Hi-Fidelity Cutter Head
Olson Cutter Head
PResto/Audax Cutter Head
Gray Research 106 16" Tonearm
PResto 1C Advance Ball
Presto k8 Motor
Presto K8 faceplate
Presto 6N Fine Pitch Feedscrews
Presto 6N Fine pitch INSIDE OUT feedscrews (extremely rare)
Presto 6N Coarse feedscrews
Presto 6NCoarse Inside Out feedscrews
You can also buy my ex-wife's cellulite massager.
This is not a fire sale. These are all FULLY FUNCTIONING, TESTED, and in most cases PROFESSIONALLY RESTORED. In most cases, the prices I am asking are what I paid for them plus the cost of their repair (not counting the sometimes 12+ months I had to wait for them to be repaired). This is not an "as-is", "only tested for continuity" or "Found in an estate" crapshoot. This stuff is all guaranteed to work well as it is (unless otherwise noted).
I've also got a TON of other random stuff. If you are looking for anything particular, let me know.
Check it out here! http://www.ebay.com/sch/accdnprone/m.html?item=321790545614&rt=nc&_trksid=p2047675.l2562
I'm cleaning out the studio a little bit to help pay for my divorce (and the gear binge depression shopping I've been doing).
I'm selling:
Presto 1C Cutter Head
RCA Hi-Fidelity Cutter Head
Olson Cutter Head
PResto/Audax Cutter Head
Gray Research 106 16" Tonearm
PResto 1C Advance Ball
Presto k8 Motor
Presto K8 faceplate
Presto 6N Fine Pitch Feedscrews
Presto 6N Fine pitch INSIDE OUT feedscrews (extremely rare)
Presto 6N Coarse feedscrews
Presto 6NCoarse Inside Out feedscrews
You can also buy my ex-wife's cellulite massager.
This is not a fire sale. These are all FULLY FUNCTIONING, TESTED, and in most cases PROFESSIONALLY RESTORED. In most cases, the prices I am asking are what I paid for them plus the cost of their repair (not counting the sometimes 12+ months I had to wait for them to be repaired). This is not an "as-is", "only tested for continuity" or "Found in an estate" crapshoot. This stuff is all guaranteed to work well as it is (unless otherwise noted).
I've also got a TON of other random stuff. If you are looking for anything particular, let me know.
Check it out here! http://www.ebay.com/sch/accdnprone/m.html?item=321790545614&rt=nc&_trksid=p2047675.l2562
I Buy/Sell/Restore Vintage Machines/Parts and Provide Phone/In Person Tech Support
www.MichaelDixonVinylArt.com
www.LatheCutCamp.com
www.RecordLatheParts.com
www.MobileVinylRecorders.com
www.LatheCuts.com
www.MichaelDixonVinylArt.com
www.LatheCutCamp.com
www.RecordLatheParts.com
www.MobileVinylRecorders.com
www.LatheCuts.com
Re: Loads of heads, feedscrews, tonearms, etc for sale
Hello.
Do you have for sale a lyrec motor of 50Hz?
Thanks in advance for your answer,
Nicolas.
Do you have for sale a lyrec motor of 50Hz?
Thanks in advance for your answer,
Nicolas.
- sunkingrecords
- Posts: 88
- Joined: Sat Feb 15, 2014 12:25 pm
- Location: Argentina
- Contact:
Re: Loads of heads, feedscrews, tonearms, etc for sale
Sorry for the dumb question, are any of thouse heads around 8ohms? i know the Presto is not, but not sure about the others
Kind regards
Kind regards
I choose not to run .-
Re: Loads of heads, feedscrews, tonearms, etc for sale
All of them are 8 ohms.... I had to take down the Olsen and RCA for a little while. I'm selling a 6N to a buddy and told him he could come over and try both to see which he preferrred. BUt one of them will be available again later.
I Buy/Sell/Restore Vintage Machines/Parts and Provide Phone/In Person Tech Support
www.MichaelDixonVinylArt.com
www.LatheCutCamp.com
www.RecordLatheParts.com
www.MobileVinylRecorders.com
www.LatheCuts.com
www.MichaelDixonVinylArt.com
www.LatheCutCamp.com
www.RecordLatheParts.com
www.MobileVinylRecorders.com
www.LatheCuts.com
- sunkingrecords
- Posts: 88
- Joined: Sat Feb 15, 2014 12:25 pm
- Location: Argentina
- Contact:
Re: Loads of heads, feedscrews, tonearms, etc for sale
Thanks!
That's interesting, i'm not in a hurry. I will try soon a borrowed Fairchild mono head and if that works I may need a replacement. Would you ship to Argentina?
Kind regards
That's interesting, i'm not in a hurry. I will try soon a borrowed Fairchild mono head and if that works I may need a replacement. Would you ship to Argentina?
Kind regards
I choose not to run .-
Re: Loads of heads, feedscrews, tonearms, etc for sale
Sure, I will ship to Argentina.... I also have nice sounding 500 ohm 1d heads that I could include a heavy duty step down transformer with...
I Buy/Sell/Restore Vintage Machines/Parts and Provide Phone/In Person Tech Support
www.MichaelDixonVinylArt.com
www.LatheCutCamp.com
www.RecordLatheParts.com
www.MobileVinylRecorders.com
www.LatheCuts.com
www.MichaelDixonVinylArt.com
www.LatheCutCamp.com
www.RecordLatheParts.com
www.MobileVinylRecorders.com
www.LatheCuts.com
- record cutter 76
- Posts: 72
- Joined: Sat Jul 14, 2012 10:07 am
- Location: tibro sweden
Re: Loads of heads, feedscrews, tonearms, etc for sale
do you have some cutter head left for sale ?? i am intrested in a mono head
what is the price on a cutter head ??
best regards from michael in sweden
what is the price on a cutter head ??
best regards from michael in sweden
- JekaTallbot
- Posts: 15
- Joined: Fri Oct 17, 2014 10:29 am
Re: Loads of heads, feedscrews, tonearms, etc for sale
Hi,
do you have stereo cutter heads left first of all?
Interested in Mono as well but this is not as important as stereo.
Greetings from Berlin.
do you have stereo cutter heads left first of all?
Interested in Mono as well but this is not as important as stereo.
Greetings from Berlin.